Perancangan Teknologi Fasilitas Kerja dengan Metode Rapid Upper Limb Assessment (RULA) dan Berdasarkan Antropometri Tubuh pada Pengrajin Daun Nipah
Abstract
Nipah craftsmen in Terjun Village, Medan Marelan District, in doing their work, tend not to pay attention to ergonomic concepts related to body posture. The aim of this research is to produce a work facility design that can help Nipah craftsmen do their work with a more ergonomic body posture. The method used in this research is to use RULA measurements and body anthropometry. Based on the RULA score, the posture of the Nipah craftsman is given a score of 5 or falls into the posture category that needs immediate change investigation. The output of this research is the design of tools to improve the posture of Nipah leaf workers. The dimensions of the work facility design are determined by the anthropometric data of the palm leaf craftsmen using the 95th percentile. The results obtained are Elbow height sitting (EHS)) of 25.71, Popliteal height (PH)) of 46.43, Elbow breadth sitting (EBS) of 46.73, Hip width (HW) of 37.73, and Shoulder height sitting (SHS) of 68,53.
References
Dewi K, Chandra. (2017). Perbaikan Postur Kerja untuk Menurunkan Gangguan Musculoskeletal Pada Industri Kecil Kerajinan Pembuatan Sapu. Jurnal Ilmiah Widya Teknik Vol.16. No2 pp 112-116.
Andriani, Meri., dan Subhan. (2016). Perancangan Peralatan Secara Ergonomi Untuk Meminimalkan Kelelahan di Pabrik Kerupuk. Prosiding Seminar Nasional Sains dan Teknologi pp. 1-10.
Oesman, Titin Isna., Irawan, Era. (2019). Analisis Postur Kerja dengan RULA Guna Penilaian Tingkat Risiko Upper Extremity Work-Related Musculoskeletal Disorders. Studi Kasus PT. Mandiri Jogja Internasional. Jurnal Ergonomi Indonesia. Vol. 05 No.1 pp 39–46.
Agustinus, Alvin., Camilia, Ayrein., dan Yoga Bonifasius. (2014). Perancangan Fasilitas Kerja pada Industri Kecil Menengah Pak Saryoto. Prosiding Simposium Nasional RAPI XII pp 165-171.
Wijaya, Irfan, Syah., dan Muhsin, Ahmad. (2018). Analisa Postur Kerja dengan Metode Rapid Upper Limb Assessment (RULA) pada Oparator Mesin Extruder di Stasiun Kerja Extruding pada PT XYZ. Jurnal OPSI Vol 11 No 1 pp 49-57.
Sulaiman, Fahmi ., dan Sari, Yossi Purnama. (2016). Analisis Postur Kerja Pekerja Proses Pengesahan Batu Akik dengan Menggunakan Metode REBA. Jurnal Teknovasi. Vol 3 No 1 pp 16-25.
Sokhibi, Ahmad. (2017). Perancangan Kursi Ergonomis untuk Memperbaiki Posisi Kerja pada Proses Packaging Jenang Kudus. Jurnal Rekayasa Sistem Industri. Vol 3 No 1 pp 61-72.
Setyaningsih, Lina., Anna, Benekdita., dan Purbasari, Annisa. (2017). Perancangan Footrest untuk Mengurangi Kelelahan Operator pada Bagian Kaki di Cell S/A Coil Xs156. Jurnal Pasti. Vol. 10 No 2 pp 126-137.
Darmawan, Satya Busi. (2009). Perancangan Meja dan Kursi pada Alat Pemotong Bulu Industri Shuttle Cock Merk T3 Berdasarkan Pendekatan Antropometri di Kelurahan Serengan Surakarta. Skripsi. Fakultas Teknik : Universitas Sebelas Maret.
Darsini. (2014). Penentuan Waktu Baku Produksi Kerupuk Rambak Ikan Laut “Sari Enak” di Sukoharjo. Jurnal Spektrum Industri Vol 12 No 2 pp 12-21.
Copyright (c) 2020 Prosiding SENTIKUIN (Seminar Nasional Teknologi Industri, Lingkungan dan Infrastruktur)
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
